Serving Brock & Parker County
Garage Floor Coating in Brock, TX
Garage, shop, and barn floor coatings for Brock and the Parker County ranchettes. Flat $6 per square foot, all-inclusive, with your price shown before we ever come out.
Local & Family-Run
Garage floor coatings, done right in Brock.
Brock is ranchette country, and ranchettes mean big garages, shops, and barns. We coat all of it, across Brock, Millsap, and the spread-out properties between Weatherford and Mineral Wells.
A working shop floor lives a hard life. We diamond-grind the slab, fill the cracks and the expansion joint, and seal it under a polyaspartic topcoat that takes hot tires, dropped tools, and chemicals without lifting. The bigger the slab, the better the per-foot price.
When folks in Brock go looking for a garage floor coating nearby, what they get from us is one of us on the phone, a clear price up front, and a crew that shows up when it says it will. Here’s our story.
- $6/sq ftAll-inclusive, shown upfront
- 2-dayInstall, done right
- LocalServing Brock, not from the city
- WarrantyWritten, on every floor
The System
A four-layer floor, built for Brock summers.
The difference between a floor that lasts and one that peels is the top layer. A polyaspartic garage floor coating cures harder than epoxy, stays clear instead of yellowing, and stands up to big shop and barn floors that work for a living. We pair that polyaspartic top with a bonded epoxy base and a full flake broadcast, so you get a real system instead of a single coat of paint.
- 1
Diamond-Ground Concrete
Day one starts with prep. We diamond-grind the slab to a clean profile and fill the cracks and the expansion joint. Cheap installers skip this step.
- 2
Epoxy Base Coat
We lay a strong epoxy base coat that bonds into the ground slab and holds the flake.
- 3
Full Color-Flake Broadcast
We broadcast Torginol color flake to refusal in the color you pick. You get full coverage and a tough surface with grip.
- 4
UV-Stable Polyaspartic Topcoat
On day two we scrape it back and seal it with a clear polyaspartic topcoat. That topcoat takes the Texas sun without yellowing.
The Honest Difference
Polyaspartic vs. epoxy: why we don’t install a bare epoxy floor.
“Epoxy garage floor” is the term everyone types, so it’s the term we use. But a bare epoxy coat, or a one-bucket kit from the hardware store, won’t survive a Texas summer. Here’s the honest difference for a Brock garage.
Bare epoxy or a DIY kit
- Yellows and chalks under the Texas sun
- Hot tires can lift it off the slab
- Usually rolled over a barely-prepped floor
- One thin coat, no flake depth, peels at the edges
Our polyaspartic system
- Stays clear and glossy in the heat
- Resists hot-tire pickup
- Diamond-ground slab, cracks and joints repaired
- Epoxy base, full flake, polyaspartic top: four layers
Upfront Pricing
Garage Floor Coating Cost in Brock
Know your price before we visit. Flat, all-inclusive pricing covers materials, labor, prep, flake, topcoat, and cleanup. You see the number before we visit.
Three things move the cost of a garage floor coating: the square footage, the condition of the slab, and the flake you pick. Our rate folds all of it into one flat number. At $6 per square foot you get the grinding, the crack and joint repair, the epoxy base, a full flake broadcast, the polyaspartic topcoat, the labor, and the cleanup. The only add-on is $1 per square foot if you want us to move everything out and set it back.
Plenty of installers post a low “starting at” rate, then the number climbs once they see your garage. We don’t work that way. The price you calculate below is the price we hold, and you get it without a salesman at your kitchen table. A typical two-car garage in Brock runs about $3,000 to $3,600, and a shop or barn floor scales straight off the same $6 per foot.
Coating, all-inclusive
$6/sq ft
Prep, grinding, crack repair, epoxy base, flake, polyaspartic topcoat, labor, and cleanup.
+ $1/sq ft if you’d like us to move everything out and put it back.
Instant Brock Estimate
This is a ballpark. Your written quote is exact and depends on slab condition and prep.
Lock In This PriceWhy It Lasts
The part most installers skip.
Coatings don’t fail because of the color. They fail at the slab. When a floor peels a year later, it’s almost always because someone rolled the coating over a smooth, dusty, or damp slab to save an hour. We grind every Brock floor to a clean profile, fill the cracks and the expansion joint, and check the slab before a drop of base goes down. That step is the job.
You also get one crew start to finish. No subcontractors and no handoffs. The same two brothers who quote your floor are the ones grinding and coating it. Every floor carries our written warranty, and since we’re a local Hood and Parker County crew, you know where to find us. Meet the team.
Pick Your Color
Real Torginol flake, your Brock floor.
Dozens of blends from clean grays to warm Hill Country earth tones.
A Real Hood County Garage
Bare concrete to showroom floor.
This is the first floor we coated. We took a tired, stained Granbury slab down to clean concrete, repaired the cracks and the expansion joint, broadcast a full flake, and sealed it under the polyaspartic topcoat over two days. Same corner, same light. It’s the floor that started the company.
Founding Customers
Be one of our first Brock reviews.
We’re coating our first floors in and around Brock right now. Book as a founding customer at founder pricing, and once your floor is done, all we ask is an honest review.
Claim a Founding SpotBrock Questions
Straight answers.
How much does a garage floor coating cost in Brock?
Our coatings start at $6 per square foot in Brock and across Parker County. That price covers prep, materials, flake, topcoat, labor, and cleanup. Want us to move everything out and put it back? Add $1 per square foot. A typical 2-car garage runs about $3,000 to $3,600, and you see the price before we visit.
Do you serve the areas around Brock?
Yes. We cover Brock and nearby Weatherford, Millsap and Aledo, plus the rest of Parker County. We live and work here, so most jobs are a short drive.
My shop floor is huge. Does that change the price?
Only in your favor. We charge the same flat rate per square foot whether it’s a one-car garage or a 40x60 shop, so a big Brock slab is strong value. One mobilization, one clean floor.
Is this epoxy?
We use an epoxy base coat as the foundation, then go further. We grind and repair the slab, lay the epoxy base, broadcast color flake edge to edge, and seal it under a UV-stable polyaspartic topcoat. A hardware-store kit skips the prep and the topcoat, so those floors yellow and lift. Ours hold up in the Texas heat.
How long does the install take?
Two days. Day one is grind, repair, epoxy base, and flake. Day two we scrape it back and lay the polyaspartic topcoat. Each stage cures before the next, and that is why the floor lasts.
Free Brock Quote
Let’s talk about your floor.
Tell us about your Brock garage and we’ll send back a firm, no-pressure price. You can also call (817) 904-3634.