Serving Benbrook & Tarrant County
Garage Floor Coating in Benbrook, TX
Garage floor coatings for Benbrook and southwest Fort Worth, built for Texas heat. Flat $6 per square foot, all-inclusive, with your price shown before we ever come out.
Local & Family-Run
Garage floor coatings, done right in Benbrook.
Benbrook sits on the southwest edge of Fort Worth, right where our service area meets the city. We coat garages and patios across Benbrook, the lake neighborhoods, and the nearby Fort Worth suburbs.
An established Benbrook garage often has a slab with a few years and a few cracks on it. We grind it back to clean concrete, repair the damage, and rebuild the surface with an epoxy base, full flake, and a polyaspartic topcoat. An old, stained floor comes out looking newer than the day the house was built.
When folks in Benbrook go looking for a garage floor coating nearby, what they get from us is one of us on the phone, a clear price up front, and a crew that shows up when it says it will. Here’s our story.
- $6/sq ftAll-inclusive, shown upfront
- 2-dayInstall, done right
- LocalServing Benbrook, not from the city
- WarrantyWritten, on every floor
The System
A four-layer floor, built for Benbrook summers.
The difference between a floor that lasts and one that peels is the top layer. A polyaspartic garage floor coating cures harder than epoxy, stays clear instead of yellowing, and stands up to older slabs that deserve a second life. We pair that polyaspartic top with a bonded epoxy base and a full flake broadcast, so you get a real system instead of a single coat of paint.
- 1
Diamond-Ground Concrete
Day one starts with prep. We diamond-grind the slab to a clean profile and fill the cracks and the expansion joint. Cheap installers skip this step.
- 2
Epoxy Base Coat
We lay a strong epoxy base coat that bonds into the ground slab and holds the flake.
- 3
Full Color-Flake Broadcast
We broadcast Torginol color flake to refusal in the color you pick. You get full coverage and a tough surface with grip.
- 4
UV-Stable Polyaspartic Topcoat
On day two we scrape it back and seal it with a clear polyaspartic topcoat. That topcoat takes the Texas sun without yellowing.
The Honest Difference
Polyaspartic vs. epoxy: why we don’t install a bare epoxy floor.
“Epoxy garage floor” is the term everyone types, so it’s the term we use. But a bare epoxy coat, or a one-bucket kit from the hardware store, won’t survive a Texas summer. Here’s the honest difference for a Benbrook garage.
Bare epoxy or a DIY kit
- Yellows and chalks under the Texas sun
- Hot tires can lift it off the slab
- Usually rolled over a barely-prepped floor
- One thin coat, no flake depth, peels at the edges
Our polyaspartic system
- Stays clear and glossy in the heat
- Resists hot-tire pickup
- Diamond-ground slab, cracks and joints repaired
- Epoxy base, full flake, polyaspartic top: four layers
Upfront Pricing
Garage Floor Coating Cost in Benbrook
Know your price before we visit. Flat, all-inclusive pricing covers materials, labor, prep, flake, topcoat, and cleanup. You see the number before we visit.
Three things move the cost of a garage floor coating: the square footage, the condition of the slab, and the flake you pick. Our rate folds all of it into one flat number. At $6 per square foot you get the grinding, the crack and joint repair, the epoxy base, a full flake broadcast, the polyaspartic topcoat, the labor, and the cleanup. The only add-on is $1 per square foot if you want us to move everything out and set it back.
Plenty of installers post a low “starting at” rate, then the number climbs once they see your garage. We don’t work that way. The price you calculate below is the price we hold, and you get it without a salesman at your kitchen table. A typical two-car garage in Benbrook runs about $3,000 to $3,600, and a shop or barn floor scales straight off the same $6 per foot.
Coating, all-inclusive
$6/sq ft
Prep, grinding, crack repair, epoxy base, flake, polyaspartic topcoat, labor, and cleanup.
+ $1/sq ft if you’d like us to move everything out and put it back.
Instant Benbrook Estimate
This is a ballpark. Your written quote is exact and depends on slab condition and prep.
Lock In This PriceWhy It Lasts
The part most installers skip.
Coatings don’t fail because of the color. They fail at the slab. When a floor peels a year later, it’s almost always because someone rolled the coating over a smooth, dusty, or damp slab to save an hour. We grind every Benbrook floor to a clean profile, fill the cracks and the expansion joint, and check the slab before a drop of base goes down. That step is the job.
You also get one crew start to finish. No subcontractors and no handoffs. The same two brothers who quote your floor are the ones grinding and coating it. Every floor carries our written warranty, and since we’re a local Hood and Parker County crew, you know where to find us. Meet the team.
Pick Your Color
Real Torginol flake, your Benbrook floor.
Dozens of blends from clean grays to warm Hill Country earth tones.
A Real Hood County Garage
Bare concrete to showroom floor.
This is the first floor we coated. We took a tired, stained Granbury slab down to clean concrete, repaired the cracks and the expansion joint, broadcast a full flake, and sealed it under the polyaspartic topcoat over two days. Same corner, same light. It’s the floor that started the company.
Founding Customers
Be one of our first Benbrook reviews.
We’re coating our first floors in and around Benbrook right now. Book as a founding customer at founder pricing, and once your floor is done, all we ask is an honest review.
Claim a Founding SpotBenbrook Questions
Straight answers.
How much does a garage floor coating cost in Benbrook?
Our coatings start at $6 per square foot in Benbrook and across Tarrant County. That price covers prep, materials, flake, topcoat, labor, and cleanup. Want us to move everything out and put it back? Add $1 per square foot. A typical 2-car garage runs about $3,000 to $3,600, and you see the price before we visit.
Do you serve the areas around Benbrook?
Yes. We cover Benbrook and nearby Fort Worth, Aledo and Westworth Village, plus the rest of Tarrant County. We live and work here, so most jobs are a short drive.
My garage floor is old and cracked. Can you still coat it?
Usually, yes. Cracks and stains are normal and we repair them as part of the prep. As long as the slab is sound, we grind it, fix it, and coat it. If there’s a deeper problem we’ll tell you straight before we start.
Is this epoxy?
We use an epoxy base coat as the foundation, then go further. We grind and repair the slab, lay the epoxy base, broadcast color flake edge to edge, and seal it under a UV-stable polyaspartic topcoat. A hardware-store kit skips the prep and the topcoat, so those floors yellow and lift. Ours hold up in the Texas heat.
How long does the install take?
Two days. Day one is grind, repair, epoxy base, and flake. Day two we scrape it back and lay the polyaspartic topcoat. Each stage cures before the next, and that is why the floor lasts.
Free Benbrook Quote
Let’s talk about your floor.
Tell us about your Benbrook garage and we’ll send back a firm, no-pressure price. You can also call (817) 904-3634.